TNEMEC

High-performance industrial coatings with unequaled aesthetic appeal, fade-resistant colors, and high gloss retention.

Innovation in Every Coat

9

Exceptional Durability

9

Unequaled Aesthetic

9

Outstanding Support

Get TNEMEC products today

Why TNEMEC

For nearly a century, Tnemec Company, Inc. has been a leading manufacturer of coatings and coating systems for exterior and interior environments.
Founded on product innovation, the company has sustained its pioneering heritage with the development of high-performance industrial coatings, designed for a range of applications from superior abrasion, chemical and corrosion resistance to interior linings, seamless flooring and wall systems, and fluid-applied thermal insulation.

9

Exceptional Durability

Exhaustive research, testing and decades of in-use performance have proven the exceptional durability of these substrate coatings.
9

Unequaled Aesthetic

Tnemec architectural coatings are known for their unequaled aesthetic appeal, fade-resistant colors, and high gloss retention.
9

Outstanding Support

Tnemec’s extensive product line is backed by outstanding technical support provided by highly knowledgeable coating consultants.

SERIES 61 | TNEME-LINER

Generic Type Cycloaliphatic Amine Epoxy
Common Usage Tightly cross-linked epoxy with excellent corrosion and chemical resistance. Principally used for immersion service, including fuel and crude oil storage, fuel pipelines, chemical containment and wastewater treatment.
Colors 5001 Gray and 5002 Beige
Finish Semi-gloss
Primers Steel: Self-priming
Concrete: Self-priming or Series 215, 217, 218
CMU: Series 215, 218
Topcoats Note: Series 61 can be topcoated with select Tank Armor linings depending on service conditions. Contact Tnemec Technical Service for recommendations.
Volume Solids 82.0 ± 2.0% (mixed) †
Recommended DFT 1. For JP-4, JP-5, JP-8, Aviation Gas and Jet A-1: 4.0 to 6.0 mils (100 to 150 microns) per coat (minimum of two coats).
2. Most Other Applications: 8.0 to 12.0 mils (205 to 305 microns) per coat (minimum of two coats). Contact your Tnemec representative for specific recommendations.
Curing Time
Temperature To Handle To Recoat Immersion
75°F (24°C) at 4.0 mils
(100 microns)
6 hours 16-18 hours• 5 to 7 days
75°F (24°C) at 12.0 mils
(305 microns)
11 hours 16-18 hours• 5 to 7 days

Curing time varies with surface temperature, air movement, humidity and film thickness.
• Maximum recoat time with itself is 7 days. Extended maximum recoat time of 14 days is allowed when used as a primer for Tank Armor products. If recoat time is exceeded, the coated surface must be scarified before topcoating.

Volatile Organic Compounds EPA Method 24
Unthinned: 0.36 lbs/gallon (45 grams/litre)
Thinned 6%: 0.71 lbs/gallon (85 grams/litre)
Thinned 10%: 1.21 lbs/gallon (145 grams/litre) †
HAPS Unthinned: 1.53 lbs/gal solids
Thinned 10%: 2.42 lbs/gal solids
Theoretical Coverage 1,315 mil sq ft/gal (32.3 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components Two: Part A (amine) and Part B (epoxy)

SERIES 971 | AEROLON ACRYLIC

Generic Type Fluid-applied acrylic insulation coating
Common Usage An innovative, fluid-applied, thermal insulating coating utilizing aerogel particles that imparts exceptional insulative properties to a variety of substrates. Ideal for insulating pipes, valves, tanks, structural steel, or other substrates where thermal improvement or personnel protection is desired. Part of a durable, corrosion-resistant coating system that bonds to the substrate, greatly reducing the issues associated with corrosion under insulation (CUI) and mitigating thermal bridging by controlling condensation.
Colors 1278 Insulation Yellow, WH13 White.
Finish Matte
Primers Steel: Series 90E-92, 90-97, 90G-1K97, 90-98, 91-H2O, 94-H2O, 115, 394, 1224. Note: The use of zinc-rich primers is not generally recommended when in-service temperatures exceed 120°F (49°C). Reference NACE SP0198 for more information.
Galvanized Steel and Non-Ferrous Metal: Series 115, 1224
Concrete: Series 1224
CMU: Series 1224
Note: Refer to appropriate primer data sheet for maximum temperature resistance.
Topcoats Series 22, 27WB, 72T, 115, 1028T, 1224. Other topcoats may be available, contact your Tnemec representative for more information. Note: A cure time of 24 hours at 75°F (24°C) is required before topcoating Series 971. Extended cure time may be required at lower temperatures.
Volume Solids 76 ± 2.0% (mixed) †
Recommended DFT 30.0 to 50.0 mils (762 to 1270 microns) per coat. Note: For use as a thermal break, recommended total dry film thickness is 80 to 100 mils (2032 to 2540 microns). Thickness may vary by project. Note: Multiple coats may be required, please contact your Tnemec Representative for film thickness recommendations.
Curing Time

Temperature To Touch To Handle To Recoat† To Topcoat
95°F (35°C) 45 minutes 8 hours 9 hours 12 hours
75°F (24°C) 2 hours 16 hours 18 hours 24 hours
45°F (7°C) 4 hours 24 hours 28 hours 36 hours

†Recoat times listed are with itself. Curing time varies with surface temperature, air movement, humidity and film thickness.

Volatile Organic Compounds 0.016 lb/gallon (1.9 grams/litre) †
HAPS 0 lb/gal solids
Theoretical Coverage 1,219 mil sq ft/gal (30.0 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components One

SERIES 1028T | ENDURATONE

Generic Type HDP Acrylic Polymer
Common Usage Water-based, low VOC, High Dispersion Pure acrylic polymer coating providing excellent long term protection in both interior/exterior exposures. Contains hollow ceramic spheres for enhanced thermal stability. May be applied by spray, brush or roller over Series 971 Aerolon Acrylic. It is mildew resistant and exhibits very good gloss and color stability.
Colors Refer to Tnemec Color Guide. Note: Certain colors may require multiple coats depending on method of application and finish coat color.
Finish Gloss – Note: Final gloss level of topcoat can vary depending on number of coats applied. One coat will generally result in a lower sheen than two coats of the material.
Intermediate Series 971
Volume Solids 46.0 ± 2.0% †
Recommended DFT 2.0 to 3.0 mils (50 to 75 microns) per coat. Important: Do not exceed 3 mils DFT when topcoating Series 971 Aerolon for personnel protection.
Curing Time
Temperature To Touch To Handle To Recoat To Resist Moisture
75°F (24°C) 30 minutes 2 hours 2 hours 6 hours

Curing time varies with surface temperature, air movement, humidity and film thickness.

Volatile Organic Compounds Unthinned: 0.61 lbs/gallon (73 grams/litre)
Thinned 5%: 0.61 lbs/gallon (73 grams/litre) †
HAPS Unthinned: 0.27 lbs/gal solids
Thinned 5%: 0.27 lbs/gal solids
Theoretical Coverage 738 mil sq ft/gal (18.1 m²/L at 25 microns). See APPLICATION for coverage rates. †
Number of Components One

SERIES 1224 | EPOXOLINE WB

Generic Type Inorganic Hybrid Water-Based Epoxy
Common Usage An advanced generation, water-based epoxy coating that is low odor and low VOC. Specifically formulated to provide a corrosion resistant barrier under fluid-applied insulating coatings as well as traditional insulation. When used as a one or two coat system, Series 1224 protects ferrous metal substrates from the effects of corrosion under insulation (CUI). Its high performance formulation offers excellent adhesion and provides exceptional protection up to 400°F (204°C). Formula protected under U.S. patent.
Colors 1288 Off-White. Note: Additional colors may be available. Contact your Tnemec representative for more information.
Finish Flat
Primers Steel: Self-priming or Series 1, 90G-1K97, 90-97, H90-97, 91-H2O, 94-H2O, 394.
Note: Series 1, 90G-1K97, 90-97, H90-97, 91-H2O, 94-H2O and 394 must be exterior exposed for one day prior to topcoating.
Galvanized Steel: Self-priming
Topcoats Series 971 Note: Series 1224 may be a suitable primer for a variety of topcoats. Please contact Tnemec Technical Services for non-insulative applications.
Volume Solids 65% (mixed)
Recommended DFT 4.0 to 8.0 mils (100 to 205 microns) per coat.
Note: Two coats may be required for aggressive exposures.
Curing Time
Temperature To Touch To Handle To Recoat
95°F (35°C) 30 minutes 3 hours 4 hours
75°F (24°C) 1 hour 4 hours 6 hours
55°F (13°C) 3 hours 8 hours 12 hours
45°F (7°C) 6 hours 16 hours 24 hours
35°F (2°C) 8 hours 6 days 8 days

Curing time varies with surface temperature, air movement, humidity and film thickness. Substrates containing integral water repellents can prolong cure times.

Volatile Organic Compounds Unthinned: 0.01 lbs/gallon (1 gram/litre)
HAPS 0.00 lbs/gal solids
Theoretical Coverage 1,049 sq ft/gal (25.7 m²/L at 25 microns). See APPLICATION for coverage rates.
Number of Components Two: Part A and Part B

Latest Projects

Bronco Drilling Company Rigs

In the Williston Basin of North Dakota, new oil discovery areas known as “plays” have business booming for Bronco Drilling Company, which is riding high with its inventory of refurbished steel rigs protected by a high-gloss industrial enamel coating from Tnemec.

“Bronco Drilling Company has made Tnemec their standard coating for all their rigs,” coating consultant Mike Cox acknowledged. “They require excellent coverage and durability, as well as color and gloss retention, which Tnemec provides.”

Louisiana Steel Storage Tanks

Concerned over the rate of interior corrosion in 38 steel storage tanks for petroleum and other chemicals, officials at a crude oil refinery in Louisiana ordered them relined using protective coatings with proven “high octane” performance from Tnemec.

“Some of these tanks had a corrosion rate on their carbon steel of up to 25 mils per year,” reported Tnemec coating consultant Eddie Borne.

“Typically, the floor thickness of a storage tank is about 250 mils, so they would have had holes in the floor of these tanks within six or eight years, which is why this project was initiated.”